Colors, Patterns and Textures of PVC, PVC-alloy and CPVC Performance Sheet


Type 1 Extruded PVC sheet

Economical, corrosion resistant, fire-rated sheet up to 1 in. (25.4 mm) thick in dark gray color for fabricating, machining and thermoforming applications

Boltaron 1050E Type 1 PVC is an extruded, corrosion resistant, fire rated sheet with normal impact resistance for fabricating, machining and thermoforming applications. Because it is a monolithic structure that is extruded to desired thicknesses (not bonded laminations) it is not subject to delamination.

Since Boltaron 1050E is also inert to harsh chemicals across the entire pH range, it is especially suited to applications in which acids and caustics are handled. And because it does not ionize like stainless steel and high alloys, it is also ideal for applications involving ultrapure water, reagent-grade chemicals or other contamination-sensitive products.

Boltaron 1050E sheet is offered in lengths to 96 in. (2438 mm), widths to 48 in. (1219 mm) and thicknesses from .060 to 1 in. (1.52 to 25.4 mm), as well as in custom blank sizes.

Smooth on both sides and free of inclusions, it is available from stock in dark gray, and offered in custom colors, custom sizes, and/or with poly masking (low minimums).

The sheet carries a UL 94 V-0 fire rating and conforms to ASTM D-1784 standards, making it suitable for a wide range of application requirements.

Boltaron 1050E is readily sawn, drilled, tapped, routed and otherwise machined using conventional tools, and can be brake formed (thinner gauges), heat welded and adhesive bonded and mechanically fastened, allowing rapid fabrication of a broad range of high-integrity parts and assemblies.

Boltaron 1050E Type 1 Extruded PVC sheet

Boltaron 1050E Type 1 PVC is smooth on both sides and offered in thicknesses from .060 to 1 in. (1.52 to 25.4 mm) in standard dark gray color.
Boltaron 1050E Type 1 PVC is smooth on both sides and offered in thicknesses from .060 to 1 in. (1.52 to 25.4 mm) in standard dark gray color.


  • Fume Hoods and Ducts
  • Machined Parts
  • Fume Scrubbers
  • Acid Etching Machines
  • Acid Tanks and Linings
  • Other Corrosion Resistant Parts

  • Solid, monolithic structure (not a bonded lamination)
  • Free of pits, voids, inclusions
  • Gauges from .060 to 1 in. (1.52 to 25.4 mm)
  • Lengths to 96 in. (2438 mm), widths to 48 in. (1219 mm)
  • Custom blank sizes at low minimums
  • Extreme chemical resistance
  • Meets UL 94 V-0 and ASTM D-1784 standards
  • Readily machined using conventional tools
  • Can be thermoformed
  • Can be heat welded, adhesive bonded, mechanically fastened
  • Custom colors and textures at low minimums


Mechanical specific gravity ASTM D-792 1.48
Tensile strength (PSI) ASTM D-638 7,400
Elongation Ultimate (%) ASTM D-638 132
Yield (%) ASTM D-638 3.5
Modulus of Elasticity (PSI) ASTM D-638 4.0x105
Flexural strength (PSI) ASTM D-790 12,000
Flexural modulus (PSI) ASTM D-790 4.2x105
Izod impact (Ft. lbs./in. of notch) ASTM D-256 1-3
Hardness Rockwell R ASTM D-785 114
Hardness Shore D ASTM D-2240 82
Compression Strength (PSI) ASTM D-695 10,830
Shear Strength (PSI) ASTM-D-732 9,240
Water Absorption 24 hrs. (%) ASTM D-570 0.032
Thermal Vicat Softening Point (C) ASTM D-1525 94
Thermal Expansion (in/inC) ASTM D-696 5.31x10-5
Heat Deflection (F) 264 PSI (annealed) ASTM D-648 156
Thermal Conductivity (BTU/HR/FT/F/in.) ASTM C-177 0.72
Specific Heat (CAL/GM/C) ASTM-C-351 0.20
Electrical Dielectric Strength (Volts/Mil.) ASTM D-149 552
Volume Resistivity (0hms/cm)x1014 ASTM D-257 1.48
Dielectric Constant (60Hz) ASTM D-150 2.910
Dissipation Factor (60Hz) ASTM D-150 0.018
Loss Index ASTM D-150 0.051
Flammability UL UL 94 V-01

1 Independent Lab Testing  


Standard Color: Dark Gray (2079) (stock)
Custom Colors: Upon Request (min. order required)
Gauges: .060 to 1 in. (1.52 to 25.4 mm)
Width: to 48 in. (1219 mm)
Length: to 96 in. (2438 mm)
Custom Blank Sizes: Upon request (min. order required)
Standard Texture: Industrial Smooth (Both Sides)
Poly Masking: Upon Request


Numerous grades of high performance PVC/acrylic alloys also available for thermoforming and fabricating applications

The application suggestions, specifications and other data described here are based upon experience and information that is believed, by BOLTARON Inc., to be reliable. However, BOLTARON Inc. makes no express or implied warranty that BOLTARON 1050E will perform in accordance with such specifications in any particular circumstance. Therefore, ALL EXPRESS OR IMPLIED WARRANTIES IN CONNECTION WITH BOLTARON 1050E, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. The prospective user should determine the suitability of BOLTARON 1050E and the application suggestions before actual application.

© Copyright 2009 Boltaron | Terms and Conditions of Sale | Sitemap